|
AASHTO Soil Classification
A soil classification system usually used for highway design and
construction.
Active earth pressure
The horizontal stress exerted by a mass of soil on a retaining wall as the wall
moves away from the soil.See the link to Retaining Walls
for equations and calculations.
Active (Rankine) zone
The area behind a retaining structure that is above the failure plane.
Activity
The ratio of plasticity index to percent by weight of clay. This property is correlated
with the type of clay.
Adhesion
The shear resistance between soil and a structure (e.g. steel, concrete
or timber piles; along a retaining wall)
Air-voids ratio
The ratio of the volume of air to the total volume of a mass of soil.
Allowable bearing capacity
The bearing pressure that can be allowed on a foundation soil, usually to limit
settlements. See the link to Bearing Capacity
for equations and calculations.
Alluvial soils
Soils deposited in a valley or slightly graded area by transporting sediments through a mountain river or streams.
American Association of State Highway Transportation Officials'
Classification System (AASHTO)
A system of soil classification based on grain size, liquid limit and plasticity of
soils.
Angle of internal friction
For a given soil, the angle on the graph of the shear stress and normal effective stresses
at which shear failure occurs. See the link to
angle of internal friction
for various relationships.
Angle of repose
The maximum angle, just before failure, of a slope composed of granular material .
Angle of shearing resistance
The ratio of effective shear and normal stresses mobilized at any state prior to
failure.
Angle of slip plane
The angle referred to horizontal of a plane or other surface along which a
discontinuous slip or rupture may occur.
Angle of wall friction
The angle of friction between soil and the surface of a retaining wall or bottom side of
a foundation.
Angular distortion
The ratio between the relative deflection between two points in a foundation
and the distance between them.
Anisotropic
A mass of soil having different properties in different directions. Primarily refers to
permeability or stress-strain characteristics.
Aquifer
A stratum of soil with relatively high permeability; a water-bearing stratum of rock or
soil.
Artesian
A condition that exists when the water table piezometric surface lies above the ground
level.
At-rest earth pressure
The horizontal stress developed in a mass of soil loaded in conditions of zero horizontal
strain. The retaining wall neither moves away or towards the soil. See the
link to Retaining Walls
for equations and calculations.
Atterberg Limits
The water contents of a soil mass corresponding to the transition between a solid,
semi-solid, plastic solid or liquid. Laboratory test used to distinguish the plasticity of
clay and silt particles.
Axial strain
Direct strain measured along an axis of a triaxial test sample.
Axial stress
Total or effective stress (Both confining and vertical stresses combined) acting along an
axis of a triaxial test sample.
Bearing capacity
The ability of the underlying soil to support the foundation loads without shear
failure.
Bearing capacity factors
Empirically derived factors used in a bearing capacity equation that usually
correlates with the angle of internal friction of the soil. See
Bearing Capacity Factors
for various tables and relationships.
Bearing pressure
The total stress transferred from the structure to the foundation, then to the soil below the
foundation. See the link to Bearing Capacity
for equations and calculations.
Bedrock
Strong rock underlying surface deposits of soil and weathered rock.
Bentonite
Sodium montmorillonite.
Borrow
A site that is used to supply soils for earthwork construction (i.e. gravel pit).
Boulders
Soil particles over 12 inches (305 mm) in size.
Boussinesq equation
An equation used to determine the increase in vertical pressure at a particular depth that
is caused by an application of a point load at a given surface. See
Boussinesq
Theory
for equations and calculations.
Braced excavation
The use of bracing to laterally support the side-walls of temporary trenches or cuts.
British Soil Classification System
A system of soil classification based on size, consistency and structure.
Bulk density
Soil density. The total mass of water and soil particles contained in a unit volume of
soil. (pcf).
Bulk unit weight
The total weight of water and soil particles contained in a unit volume of soil.
Buoyant Density
Also, submerged density. Difference between the total density and the density of water.
Buoyant density = Soil density - Density of water.
C
Caisson
A component of a particular foundation system.
California Bearing Ratio (CBR)
A laboratory test that is used to determine the suitability of of a soil for use as a
subbase in a pavement section.
Capillary rise
The height to which water will rise above the water table due to negative pore water
pressure or capillary action of the soil. See
Capillary
information in the settlement analysis and stress analysis section for
equations and calculations.
Capillary stresses
Pore water pressures less than atmospheric values produced by surface tension of pore
water acting on the meniscus formed in void spaces between soil particles.
Circular Footing
Isolated/ spread footing that is circular shaped. Usually a shallow footing.
See the link to Bearing Capacity
for equations and calculations.
Clay
Soil particles which are finer (smaller) than 0.002 mm in size.
Coarse-grained soils
Soils with more than 50% by weight of grains retained on the #200 sieve (0.075mm).
Cobbles
Soil particles between 3 inches (76 mm) and 12 inches (305 mm) in size.
Coefficient of active earth pressure
The ratio of the minimum horizontal effective stress of a soil to the vertical effective
stress at a single point in a soil mass retained by a retaining wall as the wall moves away
from the soil. See the link to Retaining Walls
for equations and calculations.
Coefficient of compressibility
The ratio of void ratio difference to the effective pressure difference of two different
loadings during primary consolidation.
Coefficient of consolidation
The rate of change of volume during primary consolidation. Units: ft�/day, m�/s.
Coefficient of curvature
Also curvature coefficient. A measure of the shape parameter obtained from a grain size
distribution curve.
CD=(D30)2/D10D60.
Coefficient of earth pressure at rest
The ratio of horizontal effective stress of a soil to the vertical effective stress at a
specific point in a soil mass behind a retaining wall when the wall does not move (loaded in
conditions of zero horizontal strain). See the link to Retaining Walls
for equations and calculations.
Coefficient of friction
The ratio between the tangential force required to cause a body, such as a foundation
surface or a retaining wall, to slide along a plane and the normal force between the body
and the plane.
Coefficient of passive earth pressure
The ratio of the maximum horizontal effective stress of a soil to the vertical effective
stress at a specific point in a soil mass behind a retaining wall as the wall moves toward
the soil. See the link to Retaining Walls
for equations and calculations.
Coefficient of permeability
See hydraulic conductivity.
Coefficient of secondary consolidation
The change in volumetric strain per a logarithmic cycle of time after primary
consolidation is complete.
Coefficient of uniformity
Also uniformity coefficient. A measure of the slope of a grain size distribution curve,
and therefore the uniformity of the soil.
Cu=D60/D10.
Cofferdam
A temporary structure used to enclose a construction area, and prevent soil or water from
entering the construction area.
Cohesionless soils
Granular soils (sand and gravel type) with values of cohesion close to zero.
Cohesive soils
Clay type soils with angles of internal friction close to zero. Cohesion is the force
that holds together molecules or like particles within a substance.
Colluvial soils
Soils deposited at the base of foot-hills via gravity or erosion.
Compaction
Volume change in soils which air is expelled from the voids, but with the water content
remaining constant. Compaction may occur due to vibration, and self-weight. In construction,
compaction is achieved by rolling, tamping or vibrating fill soils. See link
relating to Compaction
for additional information, equations and calculations.
Compression index
(Also, compressibility index) The logarithmic slope of the primary consolidation curve.
The slope of the normal compression line and critical state
line of the Casagrande Method of consolidation curves.
Compression Test
The compression test is performed in the laboratory using a relatively undisturbed ring
sample. The sample is loaded with expected building pressures to estimate the amount of
compression the soil undergoes. The sample is then
inundated with water in order to measure additional compression or swelling.
Cone resistance
The resistance force divided by the end area of the cone tip, measured during
the cone penetration test.
Cone penetration test
A penetration test in which a cone that has a 60� point is pushed into the ground at a
continuous rate. Resistance is measured by correlating the depth penetrated with the force
applied.
Confined aquifer
An aquifer that is contained between two stratifications of low permeability soil or
rock.
Confined Compression Test
See Consolidation Test
Consistency
Water content of clay relative to the Atterberg limits.
Consistency index
A measure of the relationship between the current water content and the
consistency limits.
Consistency limits
See Atterberg limits.
Consolidation
Volume change due to dissipation of excess pore pressure from static loads.
Consolidation (settlement)
The settlement of a foundation due to squeezing out of water from the pores as the soil
comes to equilibrium with the applied loads.
Consolidation test
A laboratory test in which results are used to predict consolidation of a soil under applied
structural loads. Also known as confined compression tests and oedometer tests.
Continuous footing
Also see "Strip footing." A horizontally long footing supporting a wall.
Usually a shallow footing. See the link to Bearing Capacity
for publications equations and calculations.
Coulomb earth pressure theory
An earth pressure theory that includes friction between the soil and retaining structure,
and assumes that failure occurs along a flat plane behind the retaining structure at an angle
that is in part derived from the angle of internal friction. See the link to Retaining Walls
for equations and calculations.
Coulomb's equation
Named after Charles Augustin Coulomb, (1736-1806) An equation relating the shear strength
of soil to the normal effective stress on the failure plane.
Counterfort walls
Type of retaining wall that depends on tension ribs between the stem and the heel in order
to resist flexure and overturning.
Creep
Time dependent deformations which occurs in soil at constant effective
stress without changes in volume and pore water pressure.
Critical circle
In a slope stability analyses, the slip circle that corresponds to the lowest
factor of safety.
Critical ground slope angle
The angle of the ground slope that corresponds to a factor of safety
of 1.0 relative to the slope stability.
critical height
The height of a slope that corresponds to a factor of safety of 1.0 relative to
slope failure.
Critical hydraulic gradient
The hydraulic gradient at which effective stresses becomes zero. Upward seepage.
Curvature coefficient
See coefficient of curvature.
Cyclic stress ratio
A numerical rating of the potential for liquefaction in sands.
D
Darcy's law
(After H.P.G. Darcy, 1856) The formula used for laminar flow of water through porous
saturated soils. Velocity of flow = hydraulic conductivity X hydraulic gradient.
Degree of consolidation
The proportion of consolidation that has occurred after a given elapsed time.
Degree of saturation
The proportion of the volume of water to the total volume of voids of a given mass of
soil.
Density
The ratio of the total mass to the total volume of a unit of soil. Usually expressed as a
unit weight where weight is interchanged with mass.
Units: lbm/ft�, kg/m�.
Density index
Also, relative density. The density of a granular soil relative to the minimum and maximum
densities achieved for that particular soil.
Density of soil grains
The average density of the mineral or rock of which the soil particles are
composed.
Density of water
The density of water will vary with temperature and pressure. Values used for soils
analysis are 62.4 lbm/ft�, 9.81 kN/m� or 1000 kg/m�. A value of 64.0 lbm/ft� is the value for sea
water.
Depth factor
One of the terms in the bearing capacity equation that relates to depth of the foundation.
The ratio between the depth of a slip circle below the top of a slope and the height of the
slope. See the link to Bearing Capacity
for publications, equations and calculations.
Desiccation
The process of shrinkage or consolidation of the fine-grained soil produced by increase of
effective stresses in the grain skeleton accompanying the development of capillary stresses
in the pore water.
Deviator stress
The difference between the axial and radial stresses of a triaxial test sample.
Dewater
Removal of water from a job site. Usually by pumping from excavations.
Differential settlement
The vertical displacement due to settlement of one point in a foundation with respect to
another point of the foundation. See
Settlement
analysis information for further reading.
Direct shear test
Laboratory test used to determine the relationship of shear strength to consolidation
stress. Strength characteristics that are estimated from this test includes cohesion and angle of
internal friction.
Direct strain
The ratio of the change in length to
the original length of a soil mass.
Downdrag
Negative skin friction. Forces induced on deep foundations resulting from downward
movement of adjacent soil relative to the foundation element.
Drained loading
Loading which is slow enough for the water to drain from the soil as the total stresses
increase. Pore pressure will not change, and volume will with loading.
Drawdown
The magnitude of the lowering of a water table, usually near a well being pumped.
Dredging
Removing soils from a sea, river or lake bed in order to deepen the waterway for water travel.
Dry density
The ratio of the mass of the solids (soil grains) to the total unit volume of soil.
Units: lbm/ft�, kg/m�.
Dry unit weight
The weight of solids (soil grains) to the total unit volume of soil. Units lb/ft�,
kN/m�. See unit weight
page for various tables and relationships.
Dynamic compaction
The use of high-energy impact to densify loose granular soils.
E
Earth pressure
The force per unit area exerted by soil on a retaining wall. See the
link to Retaining Walls
for additional information, equations and calculations.
Earth pressure coefficients
Coefficients used in determining earth pressure. Components may include angle of internal
friction, friction between the soil and wall face, angle of the wall face, and angle of the
sloping backfill.
Effective stress
The portion of the total stress that is supported through grain-to-grain contact of the
soil. The stress in a soil mass that is effective in causing volume changes and in mobilizing
the shear strength arising from friction. The difference between the total stress and the pore water pressure. Effective stress =
Total stress - Pore water pressure. See
Effective
stress
information in the settlement analysis and stress analysis section for
equations and calculations.
Efficiency of a pile
Also, pile efficiency. For a given pile in a group of piles, the ratio of the average
ultimate load in the group to the individual ultimate load on the given pile.
Elastic deformation
Deformation caused in a soil due to a change in loading, and the soil recovers completely
when the load is removed.
Embankment
Usually referred to a 'built-up' section of soil (engineered fill) as for roads or dams.
Engineering properties
Engineering parameters of a soil such as permeability, shear strength and consolidation.
Different from index properties. See the Laboratory Testing
link for additional
information concerning engineering properties of the soil.
Engineered fill
Soils used as fill, such as retaining wall backfill, foundation support, dams, slopes, etc.. that are to be placed in accordance to engineered specifications. These specifications may delineate soil grain-size, plasticity, moisture, compaction, angularity, and many other index properties depending on the application.
Eolian Soil
Soil deposits that have been transported by wind.
Equipotential
For a flow net, lines connecting points of equal total head. Equipotential lines are
usually drawn so that the interval, or equipotential drop, is constant. Equipotentials
intersect flow lines and impermeable boundaries at right angles.
Equivalent fluid pressure
Horizontal pressures of soil, or a combination of soil and water, which increase
linearly with depth and are equivalent to those that would be produced by a heavy fluid of
a selected unit weight.
Excess pore pressure
That increment of pore water pressures greater than hydro-static values, produced by
consolidation stresses in compressible materials or by shear strain; excess
pore pressure is dissipated during consolidation.
Exit gradient
The hydraulic gradient near an exposed surface through which seepage is moving.
Expansive Clays
Also, Reactive Clays. Clays that are sensitive to water, causing them to swell or expand.
F
Factor of safety
The ratio of a limiting value of a quantity to the design value of that
quantity. See Factor of
Safety for typical values with relation to geotechnical design.
Failure envelope
For a given soil, the graph of the shear stress and normal effective stresses at which
shear failure occurs.
Fault
A shear fracture in a rock mass along which movement has taken place.
Field density test
Also In-place density test. Field testing that determines density of compacted fill to verify
that it meets specifications. Types of tests may include sand cone, rubber balloon or nuclear
densiometer.
Fine-grained soils
Silt and clay soils. Soils containing particles smaller than No. 200 sieve or 0.075 mm in
size according to the Unified Soil Classification System.
Fines content (fraction)
Soil grains smaller than No. 200 sieve (0.075 mm), e.g. Clay and Silt.
Fissured clay
A clay having an internal network of narrow cracks or separations, in which the width and
depth tends to increase upon drying.
Fissures
Small cracks.
Flow line
The path water will follow traveling from high head to low head in a seepage flow
analysis.
Flow net
A graphical analysis of seepage flow in a mass of soil to estimate flow quantities and
pore pressures.
Flow quantity
The total volume of water flowing in a seepage analysis.
Flow rate
The ratio of total volume of water flowing to a particular unit of time.
Flow slide
Shear failure in which a soil mass moves over a relatively long distance in a fluid-like
manner, occurring rapidly on flat slopes in loose, saturated, uniform sands, or in highly
sensitive clays.
Flow velocity
The velocity of water flow through a soil.
Footing
An enlargement at the base of a foundation that is designed to transmit forces to the
soil.
Foundation
A component of an engineered structure that transmits the structure's forces into the
soil or rock that supports it. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Founding depth
The depth below the ground surface where the base of a foundation is located.
Friction angle
See angle of internal friction.
Friction pile
A pile that derives the majority of its load bearing ability from the skin friction
between the soil and the pile. See the link to Bearing Capacity
for publications, equations and calculations.
Frost jacking
A pile forced upward due to freezing ground moving upward or repeated freeze-thaw
events.
Geotextiles
A synthetic fabric used to stabilize soils, retain soils, prevent the mixing of dissimilar
soils, provide a filtering function, pavement support, subgrade reinforcement, drainage,
erosion control and silt containment. See Geosynthetics
for additional information and publications.
Grading curve
See grain size distribution curve.
Grain size distribution
See particle size distribution.
Grain size distribution curve
A curve drawn on a log scale to represent the distribution of particle sizes in a soil.
Gravity walls
Retaining walls which depend upon their self weight to provide stability
against overturning and sliding; usually made of a high bulk structure. See the link to Retaining Walls
for equations and calculations.
H
Historical maximum stress
See Pre-consolidation load.
Homogenous earth dam
An earth dam whose embankment is formed of one soil type without a systematic zoning of
fill materials.
Homogenous soils
A mass of soil where the soil is of one characteristic having the same engineering and
index properties.
Horizontal strain
Strain measured in a horizontal direction.
Horizontal stress
Total or effective stress acting in a horizontal direction.
Hveem's Resistance Value Test
Laboratory test that evaluates the resistance of a re-molded soil sample
to be used in a pavement section.
Hydraulic conductivity
Also, coefficient of permeability. The constant average discharge velocity of water
passing through soil when the hydraulic gradient is equal to 1.0. Clays are considered
relatively impervious, while sands and gravels are considered pervious.
Hydraulic gradient
Between two points in a hydraulic flow: the difference in total head (piezometric levels)
divided by the length of the flow path (distance between the two points).
Hydrometer test
Laboratory test used to determine the amount and distribution of finer particles of a soil sample. Fine soils are
classified as silts and clays. (Soils that pass the No. 200 sieve, or 0.075 mm).
Hydrostatic pore pressure
Pore water pressures exerted under conditions of no groundwater flow where the magnitude
of pore pressures increase linearly with depth below the ground surface.
I
Igneous
Rocks that were once molten. Could be intrusive (ex. granite), or extrusive
(ex. basalt).
Illite
A type of clay structure where potassium ions hold together a silica(x2) and aluminum molecule.
Immediate settlement
The settlement of a foundation occurring immediately upon loading. See
Immediate
settlement
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Index properties
Attributes of a soil such as moisture content, void ratio, specific gravity, Atterberg
limits and grain size distribution. Different from index properties. See the Laboratory Testing
link for additional
information concerning index properties of the soil.
In-place density test
See field density test.
In-situ
Undisturbed, existing field conditions.
Instrumentation
Geotechnical instruments used to monitor conditions such as deformations, pressures, loads, etc.. within the ground.
Isolated footing
Also, spread or pad footing. A footing designed to support a structural load from
a single column. Usually a shallow foundation, and square or circular in
shape. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Isotropic
A soil mass having essentially the same properties in all directions. Primarily refers to
permeability and stress-strain characteristics.
J
K
Kaolinite
A repeated silca and aluminum molecule clay structure. White mineral. Very little volume change when drying.
L
Leaching
The removal of salts and soluble substances as water flows through a soil medium. Leachate is the leached liquid from the soil, rich in minerals.
Liquefaction
The sudden, large decrease of shear strength of cohesionless soil caused by collapse of
the soil structure, produced by small shear strains associated with sudden but temporary
increase of pore water pressure. Usually a problem in submerged poorly
graded sands within the upper 50 feet of subgrade in earthquake prone
environments. See the link to Earthquake Engineering
for liquefaction equations and calculations.
Liquid limit
The water content above which the soil will flow like a liquid, but below which it will
have a plastic consistency.
Liquidity index
A measure of the relationship between the current water content of a soil and its
consistency limits.
Log-spiral earth pressure theory
An earth pressure theory that assumes that the failure surface is curved behind a
retaining structure. See the link to Retaining Walls
for publications, equations and calculations.
Long-term conditions
Conditions in the ground where full consolidation has taken place and the soils are
fully-drained.
M
Machine foundation
A foundation that receives regular or irregular vibratory loads that are generated from
rotating or impact machinery.
Mat foundation
Sometimes called a raft
foundation. A structural slab utilized as a footing, which usually
encompasses the entire building footprint. Mat foundations are advantageous
on compressible soils because the building loads are distributed over a
large area. Mats may also provide additional resistance to uplift. See the
link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Maximum dry density
A soil property obtained in the laboratory from a Proctor test. Density of soil at 100%
compaction.
Mean normal stress
The mean value of the three orthogonal stresses.
Metamorphic
Igneous or sedimentary rock that has changed by heat and/or pressure. Examples include quartz to quartzite, shale to slate, and limestone to marble.
Micropile
Piles with relatively small diameters.
Modified Proctor
Laboratory test used to determine maximum dry density and optimum moisture content of
soils. Test results are used to estimate relative compaction in the field. Soils are compacted in the
laboratory in five layers with a 10 pound hammer falling 18 inches.
Modulus of subgrade reaction
Also, subgrade modulus. The ratio between the bearing pressure of a foundation and the
corresponding settlement at a given point. The slope of the line in the loading range
encountered by the soil in a plate bearing value test. See the link to
Modulus of subgrade reaction
for typical values relating to soil characteristics.
Mohr's circle
A circle constructed in the triaxial test using the measured stresses (principal stresses)
in order to determine the stresses on the failure plane.
Moisture content
See Water content. The ratio between the mass of water and the mass of soil solids.
w = (wet weight - dry weight) / dry weight.
Montmorillonite
A clay structure that has a strong attraction to water. May swell 20x its original volume when saturated. A repeating molecule structure of 2 silica atoms and one aluminum.
N-Value
Also, standard penetration resistance. The number of blows required to drive a split-spoon
sampler during a standard penetration test a distance of 12 inches (0.305 m) after the
initial penetration of 6 inches (0.15 m).
Negative skin friction
Forces induced on deep foundations resulting from downward
movement of adjacent soil relative to the foundation element.
Nominal bearing pressure
Allowable bearing pressure for spread foundations on various soil types, derived from
experience which provides safety against shear failure or excessive settlements.
Normal compression line
The relationship between void ratio and the normal effective stress for
soil loaded beyond the current yield stress in an isotropic compression.
Normal force
Force acting normal to the plane of reference. Units: lb, N.
Normalization
Analysis of soil test data to compensate for different states of samples.
Normally consolidated soil
Soil having a current state which lies on the normal compression line.
O
Oedometer Test
See Consolidation Test
One-dimensional compression
Compression taking place with zero radial and horizontal strain.
One-dimensional modulus
The ratio of the change in vertical effective stress to the change in
vertical strain, when there is zero horizontal strain.
Open layer
A layer or stratum of soil from which porewater may drain both upward and downward into
overlying and underlying permeable layers, thus enabling two-way drainage.
Optimum moisture content
The water content at which the maximum dry density of a soil is obtained using a specific
effort of compaction. Optimum moisture of a specific soil is determined
through a Proctor test.
Organic soils
Earth comprised of organic material, peat, muskeg.
Overburden Soil
Overlying soil of a desirable soil stratum.
Overburden pressure
(Also overburden stress) The total or effective stress at a given depth
due to the weight of overlying soil or rock.
Overconsolidated soil
A clayey soil carrying a higher load in the past. Soil having a current state which lies
inside the normal compression line
Overconsolidation ratio
The ratio of maximum past pressure (preconsolidation pressure) to the current effective
stress.
Overturning
Overturning failure is a result of
excessive lateral earth pressures with relation to retaining wall resistance
thereby causing the retaining wall system to topple or rotate (overturn).
P
Pad footing
"See Isolated Footing."
Particle size characteristics
Used in particle size analyses and grading specifications: stated as
the maximum particle size of a specified percentage (smallest) of the total
content of a soil graded by mass.
D10 = maximum size of the
smallest 10% of the particle content (also referred to as effective
size)
D60 = maximum size of the smallest 60% of the particle
content
Particle size distribution
Soil particle sizes that are determined from a representative sample of soil that is
passed through a set of sieves of consecutively smaller openings.
Passive earth pressure
The maximum horizontal stress exerted by a mass of soil on a retaining surface as the
surface moves toward the soil. See the link to Retaining Walls
for publications, equations and calculations.
Peak shear strength
The maximum shear strength of a soil at a given normal effective stress and
water content.
Permeability
A measure of continuous voids in a soil. The property which allows the flow of water
through a soil. See also coefficient of permeability. See the link to
Permeability
for typical values relating to soil type.
pH value
A measure of acidity or alkalinity of groundwater or soil water extract based
on the hydrogen ion content.
Pier
A deep foundation component that is usually cast-in-place, instead of driven, drilled or
jetted as a pile.
Piezometer
An instrument used to measure in-situ pore water pressures.
Piezometric surface
An imaginary surface corresponding to the hydrostatic water level of a
confined body of groundwater.
Pile
A slender member of a deep foundation system that is driven (hammered), drilled or jetted
into the ground. Piles are usually constructed of timber, steel or pre-stressed reinforced
concrete. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Pile Driving Analyzer
A method to compute average pile force and velocity by using wave equation analysis
with electronic measurements.
Pile efficiency
See efficiency of a pile.
Pile spacing
The distance from center to center of piles.
Piping
The movement of soil particles as a result of unbalanced seepage forces produced by
percolating water. Piping leads to the development of boils or erosion channels.
Plane strain
A two-dimensional state of stress, where the out-of-plane strain (i.e. the strain normal
to the plane being considered) is zero. An example of a plane strain situation would be on a
cross-section through a long structure being loaded in the x-y plane, such as an embankment
dam.
Plastic deformation
The distortion of soil resulting in a permanent and irrecoverable change in
shape or volume.
Plastic limit
The moisture content in which a soil will have a plastic consistency.
Plastic strain
Deformation of soil that is not recovered upon unloading.
Plasticity
The property of a soil which allows it to deform continuously, usually a mass of clay
size particles.
Plasticity index
The difference between the liquid limit and plastic limit of a soil mass.
Plate bearing value
A field test that is performed on compacted soil that provides an indication of shear
strength pavement components.
Point-bearing capacity
Also, tip resistance or point capacity. The bearing capacity at the bottom tip of one
member of a deep foundation system. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Point-bearing pile
A pile that derives the majority of its loadbearing ability from the support of the soil
layer beneath the tip of the pile.
Poisson's ratio
(After Simeon Poisson 1781-1840) The ratio of the change in strain perpendicular to the
direction of loading to the change in strain caused in the same direction.
Pore air pressure
The pressure of air within the void space of a partially saturated soil.
Pore pressure
Also, hydrostatic pressure. The pressure exerted by the fluid within the pores or voids
in a porous material; in saturated soil the pore pressure is the pore water pressure.
See Pore
pressure
information in the settlement analysis and stress analysis section for
equations and calculations.
Pore pressure coefficient
The ratio of the change in pore pressure to the change in deviator stress.
Pore pressure coefficient
The ratio of the change in pore pressure to the change in isotropic stress in
undrained loading.
Pore pressure ratio
At a given depth of soil, the ratio of the porewater pressure to the vertical overburden
pressure.
Pore space
See porosity.
Pore water pressure
See pore pressure.
Porosity
Also, pore space. The ratio of the volume of voids to the total volume. Expressed in %,
or unitless.
Pre-consolidation load
The maximum load ever imposed on a particular soil mass in its geological history.
Preconsolidation pressure
The maximum past pressure of a soil.
Pressure head
The height of a column of water required to develop a given pressure at a given point.
Pressure in tension crack
The horizontal pressure exerted in a slope or against a retaining wall due to
hydrostatic water pressure in tension cracks.
Primary consolidation
The long-term consolidation of a clay from the loss of water from the voids due to a high
pressure.
Principal strains
The strains occurring in the directions of the principal axes of strain.
Principal stresses
Normal stresses acting in the direction of principal axes of stress.
Proctor test
Laboratory test used to determine maximum dry density and optimum moisture content of
soils. Test results are used to determine relative density in the field using in-place density tests. Standard
effort or Modified effort may be used in the lab. See the Laboratory Testing
link for additional
information concerning the Proctor test.
Q
Quick sand
The effective stresses within a mass of sand is zero.
R
R - Value
The R-Value, or resistance value, of a soil is measured in a stabilometer test, and is usually estimated for pavement design.
The R-value is the ability of a soil medium to resist lateral spreading due to an applied vertical load, such as tire loads. A range
of values are established from 0 to 100, where 0 is the resistance of water and 100 is the resistance of steel.
See the link to R-Values
for typical values relating to soil type.
Radial stress
In a triaxial sample, the total or effective stress acting perpendicular to the
longitudinal axis.
Radius of influence
The outer radius from a well that has a depression of water pressure or
water table produced by pumping of a well.
Raft Foundation
See mat foundation. A structural slab utilized as a footing, which
usually encompasses the entire building footprint. Raft foundations are
advantageous on compressible soils because the building loads are
distributed over a large area. Rafts may also provide additional resistance
to uplift. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Rankine earth pressure theory
Earth pressure analysis that disregards friction between the wall and soil, and assumes
that failure occurs along a flat plane behind the retaining structure at an angle that is
derived from the angle of internal friction. See the link to Retaining Walls
for publications, equations and calculations.
Reactive clays
"See Expansive Clays."
Recompression index
The logarithmic slope recompression (reloading) line.
Relative deflection
The deflection in a foundation due to settlement.
Relative compaction
A minimum density specification usually designated as a percentage of the maximum dry
density.
Relative density
Also, density index. The density of a granular soil relative to the minimum and maximum
densities achieved for that particular soil.
Remolded Swell Test
Using the same equipment as the compression test, the soil sample is remolded
and compacted in order to achieve similar earthwork conditions for the project's soils. The amount of swell can be measured after
inundating the soil sample with water after the applied loads have stabilized.
Residual soils
Soils that have been formed in place.
Resistance value
See R-Value.
Response spectrum
Information regarding frequency-dependent energy distribution of an earthquake derived
from the Fourier analysis.
Resultant force
The single force or pressure that will produce the same effect as several forces or
pressures acting along a plane. Used for easier calculations, such as analyzing earth
pressures.
Retaining wall
Walls, usually constructed of concrete or rock, that provides lateral stability of the earth, thus preventing the soil from sloughing or slope failure.
See the link to Retaining Walls
for publications, equations and calculations.
S
Sand
Particles that pass through a #4 sieve (4.75 mm), and retained on a #200 sieve (0.075 mm).
Sand cone test
Apparatus used for measuring density of soil in the field.
Saturated density
Density of soil when the voids are filled with water.
Secondary compression index
The logarithmic slope of the secondary compression line.
Secondary consolidation
The considerably decreased rate of consolidation following the completion of primary
consolidation. See
consolidation
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Sedimentary
Soils formed by the deposition of fine-grained soil in water.
Seepage
The flow of water through soil. See
seepage for
information and publications.
Seepage force
The force transmitted to a mass of soil due to the seepage of groundwater.
Seepage pressure
The seepage force per unit volume.
Seepage velocity
The average velocity at which groundwater flows through the pores of a soil. The ratio
of the volume flow rate to the average area of voids in a soil cross-section.
Sensitivity
A measure of the change in ultimate strength of clays between undisturbed and disturbed
samples.
Settlement
The downward movement of soil, or the downward movement of a foundation.
See settlement
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Shallow Foundation
Refers to a foundation system that has a shallow founding depth relative to the
foundation width. These foundations usually include spread footings, continuous footings and mats.
See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Shape factors
Factors used in a general bearing capacity equation which provides an adjustment relating
to the footing geometry.
Shear modulus
The ratio of the change in shear stress to the resulting change in shear strain.
Shear strain
The angular distortion or change in shape of a mass of soil.
Shear strength
The maximum shear stress which a soil can sustain under a given set of
conditions. For clay, shear strength = cohesion. For sand, shear strength = the product of
effective stress and the tangent of the angle of internal friction. See the Laboratory Testing
link for additional
information concerning properties of the soil.
Shear stress
The force per unit area acting tangentially to a given plane or surface.
Sheet pile
Steel section panels that are driven into the ground to provide lateral support.
Shrinkage index
The difference between the plastic and shrinkage limits.
Shrinkage limit
The water content corresponding to the transition between a brittle solid and a semi-solid.
The water content below which further reduction in water content causes no further
reduction in volume.
Sieve analysis test
Soil particle sizes that are determined from a representative sample of soil that is
passed through a set of sieves of consecutively smaller openings. See the Laboratory Testing
link for additional information concerning properties of the soil.
Site investigation
Process of methodically observing, soil sampling and field testing in such a manner that is based on proposed development and existing site conditions.
Skin-friction capacity
Also, skin resistance or side resistance. The bearing capacity for the shaft of one member
of a deep foundation system. See the link to Bearing Capacity
for equations and calculations.
Skin friction stress
The shear stress on the shaft of a pile, caisson or cone penetrometer.
Skin resistance
See skin-friction capacity.
Sliding
Sliding failure is a result of
excessive lateral earth pressures with relation to retaining wall resistance
thereby causing the retaining wall system to move away (slide) from the soil
it retains.
Slurry
A thick mixture of soil and water.
Soil classification
Standardized classification schemes that delineates soil characteristics that are
important in determining soil behavior. See the Laboratory Testing
link for additional
information concerning properties of the soil.
Soil Nailing
Slope stabilization method that involves installing and usually grouting closely spaced
rebar in the soil or rock face.
Soil suction
See capillary rise.
Specific gravity
The ratio of the density of a body or a substance to the mass of an equal volume of water.
Unitless.
Spread footing
Also, isolated footing. A footing designed to support a structural load from
a single column. Usually a shallow foundation, and square or circular in
shape. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
SPT
See Standard Penetration Test.
Square Footing
Isolated/ spread footing shaped as a square. Usually a shallow footing.
Standard Penetration Resistance
See N-value.
Standard Penetration Test (SPT)
A field
test that measures resistance of the soil to the penetration of a standard split-spoon
sampler that is driven 12 inches (0.3 m) with a 140-pound (63.5 kg) hammer dropped from a height of 30 inches
(0.76 m). The N-value is derived from this test.
Standard Proctor
See Proctor test.
Steady state pore pressure
The pore water pressure at equilibrium when all excess pore pressures have fully
dissipated.
Stiffness
Susceptibility to distortion or volume change under an applied load.
Strain
A measure of the change in size or shape of a mass of soil relative to its original
size or shape.
Stress
The intensity of force per unit area; normal stress is applied perpendicularly to a surface or
plane, shear stress is applied tangentially to a surface or plane. See
stress
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Stress history
The past history of loading and unloading of a soil mass.
Strip footing
Also see "Continuous footing." A horizontally long footing supporting a
wall. Usually a shallow footing. See the link to
Foundations or Bearing Capacity
for foundation types, applications, equations and calculations.
Subgrade modulus
See Modulus of subgrade reaction.
Submerged Density
Also, buoyant density. Difference between the total density and the density of water.
Submerged density = Soil density - Density of water.
Surcharge
An additional force applied at the exposed upper surface of a restrained soil.
See the Retaining wall
link for additional
information, equations and calculations concerning surcharges.
Suspension
A thin mixture of soil and water, whereas the soil particles are floating within the water.
Swell
Increase in soil volume; volumetric expansion of particular soils due to changes in water
content.
Swelling index
The slope of the swelling (unloading) line.
Tailings
Crushed rocks from mines after ore extraction.
Tension crack
Cracks appearing at the surface of a soil mass, often adjacent to a retaining wall or top
of a failing slope.
Tension crack depth
The depth of a tension crack from the ground surface to a depth at which the horizontal
effective stress is zero.
Tension pile
Piles that are designed to resist upward forces.
Time factor
A dimensionless quantity dependent on the degree of consolidation that is used in primary
consolidation analyses.
Tip resistance
See point-bearing capacity.
Tolerable vibration
The level of vibration magnitude that a structure is designed. Structure vibrations
range from unnoticeable to persons to structural danger.
Total head
The height of the free water surface above a given datum.
Total stress
The stress acting on or within a soil mass due to surcharges, overlying weight, etc.
Total stress = effective stress + pore water pressure. See
stress
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Transport soil
Soils that have formed, then moved to another place via wind, water, glacier, etc...
Triaxial shear strain
A strain parameter used in the interpretation of triaxial stress test results.
Triaxial stress test
Laboratory tests such as the consolidated-drained (CD) test, consolidated-undrained (CU) test
and unconsolidated-undrained (UU) test that are used to determine the soils' strength characteristics
such as cohesion and angle of internal friction.
U
Ultimate bearing capacity
The bearing stress which would cause shear failure in the soil below a
foundation; dependent upon the shear strength of the soil, applied loads and on the shape and
depth of the foundation. See the link to Bearing Capacity
for equations and calculations.
Unconfined Compressive Strength Test
Laboratory test similar to the unconsolidated-undrained test
performed on plastic soils, usually clay. From this test, the undrained shear stregth is calculated as 1/2 of the unconfined
compressive strength. Cohesion is considered to be equal to the undrained shear strength.
Undrained shear strength
(Also undrained strength) The shear strength of a saturated soil at a given
water content (or voids ratio, or specific volume) under loading conditions
where no drainage of pore water can take place. The undrained shear strength of
soil is independent of applied stresses and therefore can be measured at any
level of stress, provided the void ratio remains constant. The undrained
Mohr-Coulomb envelope will be horizontal.
Unified Soil Classification System
Known as USCS. A system of soil classification based on grain size, liquid limit and
plasticity of soils.
Uniformity Coefficient
See coefficient of uniformity.
Unit weight
The ratio of the total weight of soil to the total volume of a unit of soil.
Units: lb/ft�, kN/m�. See the
soil unit weight
link for unit weight relationships with soil type and density. .
Unit weight of water
The weight of a unit volume of water;
62.4 lb/ft�, 9.81 kN/m�.
USCS
See the Unified Soil Classification System.
V
Vane shear test
A field test used to measure the shear strength of a soil that is low-strength, homogeneous
and cohesive.
Varved clays
Clays that are layered with fine and coarse varieties.
Vertical stress
The total or effective stress acting vertically in a soil mass at a given depth caused by
the soil's own weight. See
stress
information in the settlement analysis and stress analysis section for
information, publications, equations and calculations.
Vibrodensification
The compaction (densification) of cohesionless soils by imparting wave energy to the soil
mass so as to rearrange soil particles relulting in less voids in the overall mass. Such as using a
vibratory roller.
Vibroflot
A crane suspended cylindrical penetrator with an opened water jet at the tip and acts in
conjunction with vibrations to dig a hole.
Vibroflotation
A method to densify granular soils using a vibroflot to dig a hole and then backfilled
with sand or gravel that is dumped in from the surface and densified.
Visual Classification
A field test that is used to estimate soil characteristics such as the range of particle sizes
and plasticity.
Void ratio
The ratio of the volume of voids to the volume of solids (soil grains). Unitless
Volume of solids
Volume of soil grains in a total soil volume.
Volume of voids
Volume of air space in a total soil volume.
Volume of water
Volume of water in a total soil volume.
Volumetric strain
The ratio of the change in soil volume to the original soil volume.
W
Water content
See Moisture content. The ratio between the mass of water and the mass of soil solids.
w = (wet weight - dry weight) / dry weight.
Water table
The level in a body of soil at which the hydrostatic water pressure is zero.
Weight of soil grains
The dry weight of soil grains in a mass of soil.
Weight of water
The weight of water contained in the void space of a body of soil.
X
Y
Yield point
The point at which the soil loading behavior changes from elastic to
inelastic.
Yield stress
The stress at which yielding takes place in soils. The stress at which the
swelling-recompression line joins the normal compression line.
Z
Zero air voids curve
The curve created by plotting dry densities of soils corresponding to saturation at each
water content.
Zoned earth dam
An earth dam embankment zoned by the systematic distribution of soil types according to
their strength and permeability characteristics, usually with a centrally impervious core and
shells of coarser materials.
Tell a friend! about
Geotechnical Info .Com
|
